What Did You Do To Your Boat This Week?

You can get bowls for fuel water separators that have a threaded port for a water sensor. The sensor connects to the engine harness, for Mercury at least, not sure about others. You get an alarm when there's water in the bowl, before it's so much water that the engines gets any.

I had a plastic secondary tank that got a bunch of water in it a while back. Had to drain the racor every 10-15 minutes, but never got any water in the engine. From my perspective a fuel water separator without an alarm isn't worth a lot unless it's only ever going to see very small amounts of water. You would need to check it far more regularly than anyone I know does and as described above, some times you can't tell easily if it's full of water or fuel.
 
Sharphooks said:
Thanks for the support. Yes, I’ve always carried a separate 20L tank for the T25 kicker. I knew some day it would save my bacon. The main reason, though, is I can track fuel burn better in the summer….when running the T25 off the main tank, the fuel burn doesn’t get registered by the digital fuel gauges that are hooked up to the DF300’s…it’s a big back deck so that tank is easy to shove out of the way while fishing


View attachment 116187
Click to expand...
A veteran move with the redundancy
 
I noticed the loom protecting the threads on the steering connector arm between the kicker and main was getting torn up so I had to investigate.
I turned and tilted the motors through every possible permutation and found the rubbing occurred while the kicker was fully tilted up and the main was down and turned hard either way (both ends).
The kicker has an after-market bracket at the front with three attachment points so as I was going through every position I also measured the distance from the main to the starboard position instead of the center one where it was installed at the dealer. It was apparent that this would work better and eliminate the binding/rubbing so I cut 4” off the arm and re-installed it. I also slid a piece of 3/8 fuel line over it instead of loom as I thought it was a cleaner look.
 

Attachments

  • IMG_8328.jpeg
    IMG_8328.jpeg
    304.3 KB · Views: 85
Sharphooks said:
Hey RB—-It’s interesting that your boss had the same issue with his XL2400….I say that because when I limped back to the dock after breaking down I just happened to a see a Seasport 24 tied up and noticed that the gas caps were mounted up on the wheelhouse walls —my first thought was —if my caps were mounted vertically and off any surface that could pool water, I’d be out fishing, not having to belly up to the bar with $2K in hand to get all my filters changed out, injectors cleaned , and VST’s drained

So here’s what I know—-Perko caps have a KNOWN issue. They even include a fine-print add-on that warns installers not to mount the caps where water can pool. Gas tanks expand and contract and when they contract they create a vacuum that will suck standing water through the Perko caps and down into the tank.

Perko offers a “riser” that is designed to shim the caps off whatever flat surface they are mounted to. I tried to install the risers last summer but I couldn’t get at the hose clamps under the deck to loosen up the filler tubes (at least without cutting fiberglass which is beyond my pay grade) so I gave up

NMI (Northwest Marine Industries) is a stand-up company. They stand behind their products and if there are issues, my experience is they will help to address them.

You might have your boss call them. I mention that because as mentioned above, it was explained to me that the charcoal filters (for vapors and overflow during refueling) that are now mandated by the EPA will clog up which only exacerbates the tank expansion and contraction issues (no venting!) So couple that with a crappy cap that leaks and you can see how both rain and salt water splash are getting into the tanks

If you want a private contact for NMI, PM me, especially if your boss has a newer XL2400
Click to expand...
i’m not sure what brand the fillet cape were but they were flush mounted on the starboard gunnel . slightly aft of the wheel house. the cape were different colours to represent fuel vs water.

they ended up selling the boat; i just thought wow what a coincidence.

now i’m wondering about my o-ring. think i’m gonna go inspect mine.
 
DanJ said:
Looks fantastic. I have had two surgeries for herniated discs so I feel your pain. Keep that core strong. It sure helps.
Click to expand...
I have an old ski injury - compression fracture when I was much younger and never really worked on my core strength. I was lucky and never had serious back issues following, however after a day of skiing or any hard work I'd have back strain. Last year I took up rucking (fancy way of saying I carry a weighted pack) - I walk to the skytrain and home every day for my commute (maybe 6000 steps) - first with a 25lb pack and now with 35lbs. Totally transformed my ski season and built up a lot of useable core strength/stability. Lots of guys claim you can lose a ton of weight this way - but that wasn't my experience - minor weight loss (maybe), no beauty muscles, just strength for when you need it.

Don't take that as a suggestion while you are recovering - but maybe at some point in the future.
 
Max123 said:
I have an old ski injury - compression fracture when I was much younger and never really worked on my core strength. I was lucky and never had serious back issues following, however after a day of skiing or any hard work I'd have back strain. Last year I took up rucking (fancy way of saying I carry a weighted pack) - I walk to the skytrain and home every day for my commute (maybe 6000 steps) - first with a 25lb pack and now with 35lbs. Totally transformed my ski season and built up a lot of useable core strength/stability. Lots of guys claim you can lose a ton of weight this way - but that wasn't my experience - minor weight loss (maybe), no beauty muscles, just strength for when you need it.

Don't take that as a suggestion while you are recovering - but maybe at some point in the future.
Click to expand...
I just got back from getting needled, stretched and electrocuted! I’ll wait for a bit more before I start with a weighted pack. I do like backpacking so maybe I’ll have to start with some weight in my pack out for my evening walk in a week or two.
 
I know I shouldn't went boating on good Friday, but my colleague wanted to go for a boat ride. Plus I wanted to see how the Hattie 9.8 worked. Started in three pulls. Didn't hurt my shoulder.
Got the df-14 going up to 17 mph. Surpassed my expectations. 😃 just gotta see how fast with one person.

As for the seamax 65lbs trolling motor i got from boat show...it lasted 1 minute. My battery was dead.

Plus I know she can handle 11 knot winds. How much more ? Must find out before I go to English bay.
 

Attachments

  • IMG-20250418-WA0005.jpg
    IMG-20250418-WA0005.jpg
    269.2 KB · Views: 40
kaelc said:
Couple weeks out before she gets mounted but heading home on the ferry a much poorer man but smilin!
Click to expand...
That 150 is a beauty - while everyone always likes the idea of squeezing every last hp out of the block, I appreciate owning an engine that is somewhat understressed.

Keep in mind that while the Suzuki 2.9L block may be rated between 150-200hp, all motors in that range offer very similar peak torque. The 150hp model puts out 237nm @ 4000rpm, whereas the 200hp model tops out at 249nm @ 4000rpm. Likely the only difference is a milder cam, and a higher redline.


Happy Boating - don't forget to follow the break-in procedure
 
Max123 said:
That 150 is a beauty - while everyone always likes the idea of squeezing every last hp out of the block, I appreciate owning an engine that is somewhat understressed.

Keep in mind that while the Suzuki 2.9L block may be rated between 150-200hp, all motors in that range offer very similar peak torque. The 150hp model puts out 237nm @ 4000rpm, whereas the 200hp model tops out at 249nm @ 4000rpm. Likely the only difference is a milder cam, and a higher redline.


Happy Boating - don't forget to follow the break-in procedure
Click to expand...
Yeah, and my boat gets squirly and pounds at high speed, at least that helped me justify it. It came with a much larger prop 16"x17p and the gear ratio should be good for the additional torque I'm getting. Even the mechanic owner at North Shore Marine was surprised at how much oil it takes. As long as it can get up swells a little bit better when loaded to the gills, I can continue to invite my 250lb+ friends on multi day missions. It's not good when you wonder how much crab bait they would make and how much better the boat would run when a 250lb guy walks around, affecting the performance.
 
Replaced surge acuator as starting pissing out brake fluid to discover my calipers are seized . Brake out another thow…
Did wheel bearings while had it all apart .
Beer time now
 
You must log in or register to reply here.

Similar threads

C
Need to clarify current taxes for a used boat, trailer and gear.
Replies
47
Views
2K
kaelc
kaelc
C
Aluminum care
Replies
11
Views
914
chille51
C
Stizzla
PINCH ME
Replies
122
Views
11K
Stizzla
Stizzla
Newf
Another charger question.
Replies
8
Views
945
landcrab
L
J
lessons learned from buying a 10 year old boat
Replies
33
Views
4K
sly_karma
sly_karma
Back
Top