What Did You Do To Your Boat This Week?
- Thread starter Stizzla
- Start date
That's a nice '56 ya have on the rack back there !!
baddogg
Crew Member
Ya, not mine unfortunately. It's been up on that hoist for 3 years now.
@ Stizzla, some clarification. It's special to me, but not compared to a lot of the boats on this forum. Hoping for many years of trouble free boating and fishing now.
@ Sea Chaser, I'm fortunate to have this building
@ Oly 1, it's a work in progress keeping it tidy
sir-vivor
Well-Known Member
Got the old cable steering off and the new Seastar Support Bar on the old Ocean Pro , WITHOUT lifting the engine. Had to file down a bit of the opening in the washwell boot but alls good. 3 hours of thinkin and 1/2 for coffee brake and 1/2 to do it . Next , attach all the hardware and cut the hole larger at the helm for the pump. I sure hope its better than the cable lol
ab1752
Crew Member
Today's fun and games in boating has been changing the raw water impeller. What a gigantic pain in the butt on our boat, the access area is just too small. Then the lower hose to the heat exchanger is only 3" long max, very little flex. And of course, one of the bronze screws is now rolling around the bilge. Have to head back this afternoon and vacuum it out ahhhh!
I've done this 4 times, every 2 years and curse it every time. Stupid volvo haha
Going to drain the manifolds this afternoon as the impending cold snap is a bit concerning. Say a prayer for my kicker, k?
I've done this 4 times, every 2 years and curse it every time. Stupid volvo haha
Going to drain the manifolds this afternoon as the impending cold snap is a bit concerning. Say a prayer for my kicker, k?
Rain City
Crew Member
Yeah I've yet to ever do anything to my kicker over the winter. I put a heater in the engine bay. What do guys do?
ab1752
Crew Member
Not much, just gonna drain the raw water side on the IO manifolds and such then burn some effigy to the kicker gods and hope for the best. When the boat was dry stored i would run it up with rv coolant same as others. I hear some guys are using compressed air to blow water out now but that seems like a pita so here goes nuttin!
ab1752
Crew Member
Now that I think of it im gonna warm the kicker up with some sweet, sweet salt water and leave it at that. Some vague high school chem memory says salt water has a lower freezing point than the fresh thats in there now so wtf, nothing to lose.
Rain City
Crew Member
I'll probably just run it a couple times too.
Newf
Crew Member
Changed the cutlass bearing last week. Had to remove the batteries and box to provide enough access to pull the coupling off of the shaft for it's removal. Made up a couple of pullers for the coupling and prop removal and overall things went well. My first time doing this so I was in no rush. Will clean things up tomorrow and reinstall, complete with new stuffing box hose and packing.
kingblazer84
Crew Member
Stizzla
Crew Member
No more mixing oil and gas for you!
ReelSlim
Crew Member
Well I didn't install these this week but it is -40C today and I'm missing my boat big time! I ordered these in from Florida last Spring from Deep Blue Tackle. They make custom stuff as well but I found ones that were going to work for my needs. Very well built and good hardware as well. Not sure what those pieces of painted aluminum that I cut out cost me but I don't think the builder is taking any buy backs? lol And yes I know that 1 of the 4 3700 series tackle boxes doesn't match. That too has been rectified. 
Attachments
walleyes
Well-Known Member
Very nice, those look very well built.Well I didn't install these this week but it is -40C today and I'm missing my boat big time! I ordered these in from Florida last Spring from Deep Blue Tackle. They make custom stuff as well but I found ones that were going to work for my needs. Very well built and good hardware as well. Not sure what those pieces of painted aluminum that I cut out cost me but I don't think the builder is taking any buy backs? lol And yes I know that 1 of the 4 3700 series tackle boxes doesn't match. That too has been rectified.
bigbruce
Crew Member
Reworked my NMEA 2000 network to have it switched via an Acc switch on the dash. Will be installing a Fox Marine Gateway on my Volvo engine when it arrives this week. Removed a Garmin GFS 10 fuel flow meter and replaced the fuel line. Traced and repaired a broken ground wire that had rendered my bait well pump and bilge float switch inoperable.
And, put a shitload of bandaids on the back of my hands from the nicks and scratches associated with working in an engine well...
And, put a shitload of bandaids on the back of my hands from the nicks and scratches associated with working in an engine well...
Last edited:
Stizzla
Crew Member
Stizzla
Crew Member
Not unless fire is a common review.
Similar threads
