eaglemaniac
Well-Known Member
That's some real Mcgiver stuff you got goin on there Mike.
eman
eman
Fugly-2 -Less Fugly-The rebirth of a Legend...
- Thread starter jeffywestcoast
- Start date
RiverBoy
Well-Known Member
That's some real Mcgiver stuff you got goin on there Mike.
Yah I was gonna say it looks a bit primitive, but I would use wooden Popsicle sticks hot glued together before I would use an EZ Steer system. Words can't describe how much I hate EZ Steer.
Just search it on this forum.
Sangster21
Member
I have an EZ steer from my mercruiser leg to my kicker (also a Mercury Pro Bigfoot) and it works just fine! I leave it on all the time, I do have to do a little syncing between the kicker and main, but it works OKey dokey.
Alan
Alan
fish brain
Crew Member
That is a cool rig Mike. I see a cable to your shifter. how does that work?
jeffywestcoast
Well-Known Member
I still have the bracket we made last year and the bar ends.. That is the closest i have seen yet..
Sent from my iPhone using Tapatalk
RiverBoy
Well-Known Member
Mine never synced properly from day 1. Followed the instructions to the tee. Called customer service. Less than helpful. The thing would pull apart on every turn. Crank it down. Still pull apart. The only time it ever worked was when I cranked the detentes so tight it was effectively a straight bar. Then I discovered the ready rod ball joint method and never a problem. Sold the EZ Steer on this forum the next day.
jeffywestcoast
Well-Known Member
I Really think the offset might be too much for the eze- steer..i think a custom rod set up Like Mike_R has might be possible tho.. Sculpin what do you think?
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
finaddict
Well-Known Member
Brand name is Stearns. The stainless one with brackets that fit the main motor runs about $60.00. I have one and I really like. Far superior to an EZ Steer and far less dangerous than trying to hook up when off shore. ;-)
buzzbomb
Well-Known Member
Need more photos.......
Are you able to get out that far to start that thing safely?
Are you going to clean up the bottom paint or remove it?
When are you going to take that boat out for a spin? Be sure to take more photos when you do
BuzzBomb said what?What does he know
Lol you sound like my wife. Jeffys got his work cut out for him in the steering department ( I know just went through the same thing on my DE) but seems to have enough prop depth and lots of hight to keep out of back rollers.
SpringVelocity
Crew Member
On the engine in front you should have a threaded tab that sticks out. It looks just like that one above.... The only thing is on old motors it doesn't stick out that much and you may need to extend pivot point (LOLOL that sounds bad )Get a simple 1" x 2 to 3" stainless drill two holes... You attach and bolt/nylock nut to your motor, and than attach the threaded ball joint to that...Don't put that cheap panther bar there frankly POS.. I went thru two of them rusted out/screwed up... HC and I think Trotac have the one you need its that's totally stainless..Its 100.00 machined locally ..Its a threaded rod with then ends all machined completely solid ..Bend it like that one you see up in pic...Like a slight S..On the Yamaha on mine it had a place to put the other threaded ball joint... All you do is simple connect or disconnect... Dead simple.
Quite frankly I think EZ steer sucks complete butt,and I am not looking forward to putting it on my boat... Only reason is I am going outboard to inboard...Trust my Jeff the system works awesome. I ran exact setup as you... This system is good because you can unhook it inside boat not leaning over to get to in water like EZ steer.
Last edited by a moderator:
jeffywestcoast
Well-Known Member
I ran that system last year, all i would need is a lengthened ty bar bent in that funny angle and a extension bar off the front of my kicker that would either disconnect or tilt when the motor tilted all the way up for travel...
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
jeffywestcoast
Well-Known Member
Never thought of that but dont want to drill holes in it,with the tiller arm where it is at now it does swing free above the transom.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
jeffywestcoast
Well-Known Member
Thanks califbill, my kicker is a couple of posts back but i agree with you , a thin sheet of UHMW would help to keep mike_r's tiller handle from wearing out .
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
salmonkiller01
Well-Known Member
Pretty Much impossible to use a steering bar out front, we re- used existing holes from the previous kicker bracket, going to put the boat in today but Buzzbomb said it looks good where it is, sits pretty high up but i would rather that then have it submarine on me..
Sent from my iPhone using Tapatalk
Didn't you have enough room to mount the kicker on the side of your big motor in the splash well? My buddies double eagle has the kicker mounted there, it does rub a little trimmed up but steers fine. Will get a pic for ya.
jeffywestcoast
Well-Known Member
Imagine in picture three if you turned the main to the left,the steering cable that goes thru the tilt tube extends further over to the port side..
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
jeffywestcoast
Well-Known Member
In other news.. I picked up another hds gen 2 5inch this one is a fishfinder/gps and also i picked up the lowrance cable to link the two, and a copy of Navionics gold.
pretty near have a full dash now minus the sound system..
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
